kknhsihp

Moderator: Angel

Post Reply
cnrob1
Contributor
Contributor
Posts: 3
Joined: Mon Jun 08, 2009 8:07 pm

HL-S5086W...3 Blinking Lights of Death

Post by cnrob1 » Mon Jun 08, 2009 8:18 pm

Hopefully someone can point me in the right direction. Been researching through the forums, but have not seen anything similiar to my problem. Obviously, have the three blinking lights which could mean several things.
I have replaced the lamp and reset the lamp meter, but still have following issue:

Once i turn tv on, everything appears to work fine. Colorwheel spins, both fans on, lamp ignites and screen looks perfect.
After about 5 minutes, lamp blinks once and power shuts down, and the 3 blinking lights of death resume.

I have ordered a DMD board, but now thinking it could be the ballast or temperature sensor based on some of the posts here...
Has anyone had an experience like this?

Thanks
Top
User avatar
Kelly
Self-Proclaimed Guru
Self-Proclaimed Guru
Posts: 56
Joined: Thu Mar 12, 2009 10:04 pm

Re: HL-S5086W...3 Blinking Lights of Death

Post by Kelly » Mon Jun 08, 2009 9:48 pm

cnrob1 wrote:Hopefully someone can point me in the right direction. Been researching through the forums, but have not seen anything similiar to my problem. Obviously, have the three blinking lights which could mean several things.
I have replaced the lamp and reset the lamp meter, but still have following issue:

Once i turn tv on, everything appears to work fine. Colorwheel spins, both fans on, lamp ignites and screen looks perfect.
After about 5 minutes, lamp blinks once and power shuts down, and the 3 blinking lights of death resume.

I have ordered a DMD board, but now thinking it could be the ballast or temperature sensor based on some of the posts here...
Has anyone had an experience like this?

Thanks

It could be the lamp. You may have gotten a bad one. I would send it back for an exchange before doing anything else.
Top
cnrob1
Contributor
Contributor
Posts: 3
Joined: Mon Jun 08, 2009 8:07 pm

Re: HL-S5086W...3 Blinking Lights of Death

Post by cnrob1 » Tue Jun 09, 2009 9:17 pm

Lamp is good...any other ideas?
Top
User avatar
Angel
Site Admin
Site Admin
Posts: 446
Joined: Sat Apr 04, 2009 1:52 am

Re: HL-S5086W...3 Blinking Lights of Death

Post by Angel » Wed Jun 10, 2009 3:37 pm

cnrob1,

What happens if you try to turn the TV ON just after it turns itself off? Any noises?

I think this is an overheating issue, check the fans and air vents for dust.
The best "Do It Yourself" site for all types of Displays!
Top
cnrob1
Contributor
Contributor
Posts: 3
Joined: Mon Jun 08, 2009 8:07 pm

Re: HL-S5086W...3 Blinking Lights of Death

Post by cnrob1 » Wed Jun 10, 2009 6:50 pm

Yeah...When I turn it on, it emits high short notes in a morse code sequence, but light will not turn on


Thanks for your help...
Top
User avatar
Angel
Site Admin
Site Admin
Posts: 446
Joined: Sat Apr 04, 2009 1:52 am

Re: HL-S5086W...3 Blinking Lights of Death

Post by Angel » Wed Jun 10, 2009 10:01 pm

When you open the back door and take out the lamp assembly, the temp sensor is located above, embedded to the light engine assembly.

HTH.
The best "Do It Yourself" site for all types of Displays!
Top
MiafUp
TV Wizard
TV Wizard
Posts: 489
Joined: Thu Apr 23, 2020 10:53 pm

kknhsihp

Post by MiafUp » Wed Nov 16, 2022 3:31 am

ciprofloxacin hcl 500 mg
Top
Post Reply

Return to “Akai DLP Discussion”